Ps23.co.za

IDENTIFICATION
PS23 PROTECTO LITHIUM COMPLEX GREASE
CAS: Not applicable to mixtures.
UN: None allocated.
PS23 Manufacturing & Distribution (Pty) Ltd
P O Box 75626
Lynnwood Ridge
0040
Republic of South Africa
AFTER HOURS EMERGENCY NUMBER:
+27 - 12 - 808 0655
COMPOSITION:
This product is a secret blend of petroleum-derived grease, with additives: Highly refined base oils
Mineral oil, petroleum distillates, solvent dewaxed heavy paraffinic

NIOSH No: PY8038500ACGIH TLV: 5 mg / m3 (oil mist) Additives, which may include:
Thickeners, rust inhibitors, extreme pressure agents, emulsifiers, tackifiers,
antifoam agents, and corrosion inhibitors
Ingredient sequence number 2
CAS No:
Proprietary Blend
Ingredient sequence number 3 is added for extreme pressure enhancement.
HAZARDS IDENTIFICATION
TO THE ENVIRONMENT
FIRST AID MEASURE
SYMPTOMS AND EFFECTS
Health Effects
No specific data is available for the product for chronic exposure symptoms. Thematerials in this product are not considered to be carcinogenic by the Work safeAustralia lists (October 1991).
ACUTE EFFECTS
Inhalation: The product may be considered to be non toxic
there is no reason to expect that inhalation of the mist will give rise to anyhealth effects.
Data suggests that this product should be classified, as no more than amild transient irritant to the eyes, no long-term effects are likely.
Ingestion: Data suggests that the product should be considered to be non-toxic by
Data suggests that this product should be classified as not irritating orotherwise harmful to the skin. Prolonged and repeated contact mayhowever cause dermatitis due to the defatting effect on the skin. High-pressure accidental injection through the skin requires immediate medicalattention for possible incision, irrigation, and / or debridement.
FIRST AID
Product Inhalation:
The formulated product is a gel. Inhalation is thereforealmost impossible and only mist can be inhaled. If anysymptoms should occur remove the victim to fresh air. Laythe victim down and keep warm and rested. If breathingis shallow, or has stopped, ensure a clear airway and applyresuscitation or oxygen if available. Transport to the nearesthospital or doctor immediately.
Product in eye:
If this product comes in contact with the eyes, hold the eyeopen and flush with running water. Ensure irrigation underthe eyelids by occasionally lifting them. Do no try to removecontact lenses unless trained. If any irritation does occur,consult a medical doctor.
Product Ingestion:
Ingestion of a small amount is not expected to be a problem,however if more than a litre is ingested, do NOT inducevomiting, rather get the victim to drink a glass or two ofwater, and take the victim to a doctor or hospital.
Product on skin:
The product has no effect on the skin in normal use, no firstaid is therefore applicable, merely wash the area with soapand water. Remove contaminated clothing and footwear.
Ensure that contaminated clothing is laundered before usingagain.
Advice to Physician:
Treat symptomatically. Note the nature of this product FIRE-FIGHTING MEASURES
Flash point:
EXTINGUISHING MEDIA
Small or large fire:
There is a moderate risk of an explosion from this product if involved in a fire. Intenseheat may cause violent rupture of containers. The decomposition products are toxic.
Decomposition products: Carbon dioxide, carbon monoxide, and water.
Polymerisation:
Stability:
Materials to avoid:
Strong acids, strong bases, strong oxidizing agents.
PROTECTIVE EQUIPMENT
Wear protective clothing including facemask, face shield and gauntlets.
Self-contained breathing apparatus should be used.
ACCIDENTAL RELEASE MEASURES
Personal protection:
Wear full protective clothing including facemask, face shield,and gauntlets.
Small spillage:
Shovel into labeled containers for recycle or disposal.
Large spillage:
Stop leak if able to do so and contain the spill. Shovel the
material into labeled containers for recycle or disposal.
Recycle the material, and containers, whenever possible.
After a spil , wash the area, preventing runoff from entering
the drains. Slippery on floors especially when wet.
Environmental precautions:
In the event of a major spill, prevent the spill from entering drains or watercourses.
Dispose only in compliance with local, state, and federal regulations. Report spills to theappropriate authorities. The material may be suitable for disposal in approved, landfills.
HANDLING AND STORAGE
Handling:
This material has no UN Classification, requires no special handlingrequirements, and is not a scheduled poison.
Storage:
Containers should be kept closed to avoid contamination. Keepaway from extreme heat and open flames. Store away from strongacids, strong bases, and strong oxidising agents.
PERSONAL PROTECTION / EXPOSURE CONTROLS
OCCUPATIONAL EXPOSURE STANDARDS
A time weighted average (TWA) concentration for an 8-hour day and 5-day workingweek has not been established for this product. A TWA of 10mg / m3 is howeverrecommended for inspirable dust and mists when limits have not been otherwiseestablished. The nature of this product makes it unlikely that this level will beapproached in normal use. See ingredients section of this data sheet (paragraph 2).
ENGINEERING CONTROL MEASURES
The hazardous practice of dropping containers from delivery vehicles should beavoided. The correct equipment for handling the containers should be used. Theventilation of the areas used for storage, discharge or dispensing should be as normallyrequired for chemical handling areas. Concentration values below the TWA value(above) should be maintained. Values may be reduced by process modification, use oflocal exhaust ventilation, capturing substances at source, or other methods. If it isbelieved that air borne concentrations of mists, dusts, or vapours are high, it is advisedthat process or environment be modified to reduce the problem.
PERSONAL PROTECTION
Respiratory:
None under normal use. Rubber, PVC, or other protective glovesare desirable if the product is to be used frequently or for extendedperiods None unless splashing is likely to occur e.g. When applying thegrease overhead, when eye protection should be worn PHYSICAL AND CHEMICAL PROPERTIES
Appearance:
Boiling point / range:
No data, likely to decompose before boiling Melting point / range:
No specific melting point. Drop point is above 230 0 C Flash point:
Flammable limits:
Explosive Properties:
A moderate risk of explosion at extreme temperatures Vapour pressure:
Density:
Solubility in water:
Corrosiveness:
Viscosity:
10. STABILITY AND REACTIVITY
Stability:
Incompatible materials: Strong acids, strong bases, and strong oxidising agents.
Hazardous decomposition products:
Carbon dioxide, carbon monoxide, and water 11. TOXICOLOGICAL
INFORMATION
ACUTE TOXICITY
May be irritant on prolonged use by sensitive individuals.
Inhalation:
Mists in air up to 10mg / m3 are considered safe.
CHRONIC TOXICITY
Not available, but not expected to be toxic under normalexposure conditions.
IRRITATION
General y non-irritating, but may cause slight irritation insensitive individuals, or if used repeatedly, or for prolongedperiods due to the defatting of the skin.
Respiratory:
Inhalation is not expected to be a problem unless theconcentrations are high.
CARCINOGENICITY
No evidence to indicate carcinogenic toxicity.
MUTAGENICITY
No evidence to indicate mutagenic toxicity.
REPRODUCTIVE HAZARDS
No evidence to suggest reproductive toxicity 12. ECOLOGICAL
INFORMATION
This product is not soluble in water and there is no evidence that any lasting ecologicaldamage will result from a spillage. It is however advised that spillage should be avoided,and that every precaution should be taken to prevent the product entering theenvironment.
13. DISPOSAL
CONSIDERATIONS
Disposal methods
This product is not specifically listed by the EPA as a hazardous waste (40 CFR, Part261D) nor is it formulated to contain materials, which are listed as hazardous wastes. Itdoes not exhibit the hazardous characteristics of ignitability, reactivity, or corrosivity,and is not formulated with contaminants as determined by the Toxicity CharacteristicLeaching Procedure (TCLP). However used product may be regulated.
Dispose only in compliance with local, state, or federal regulations.
Suitable for incineration in a controlled burner, for fuel, or disposal Classification:
Disposal of packaging:
14. TRANSPORT
INFORMATION
UN Classification:
ADR/RID:
IATA - Class:
15. REGULATORY
INFORMATION
National legislation:
EEC hazard classification:
Risk phrases:
Not considered hazardous in normal application.
Safety phrases:
16. OTHER
INFORMATION
APPLICATION OR USE OF THE PRODUCT
Lubrication grease for extreme pressure applications 17. REFERENCES
The material safety data sheets supplied by the manufacturers and suppliers of theingredients, and from Cornell University (US), MSDS data files 18. EXCLUSION OF LIABILITY
The information given in this document is based on product knowledge at the date ofpreparation and is offered in good faith. Responsibility cannot be accepted for any erroror omission therein, or damage that may result.

Source: http://www.ps23.co.za/Downloads/MSDS%20-%20Protecto%20Lithium%20Complex%20Grease.pdf

lsmu.deform.lt

Svarbiausios pastarųjų metų publikacijos 1. Borutaite V., Morkuniene R., Valincius G. Beta-amyloid oligomers: recent developments. BioMolecular Concepts. 2011, 2(3): 211–222. 2. Barauskaite J, Grybauskiene R, Morkuniene R, Borutaite V, Brown GC. 3. Cizas P, Budvytyte R, Morkuniene R, Moldovan R, Broccio M, Lösche M, Niaura G, Valincius G, Borutaite V. Size-dependent neurotoxicity of

© 2010-2017 Pharmacy Pills Pdf