DURACON® 304 A GENERAL PURPOSE SEALER FOR Packaging DURACON FLOORING SYSTEMS
Shelf life
6 months when stored in a cool and dry place and in original-
KEY BENEFIT SUMMARY
ly closed packaging. The optimal storage temperature is 15 -
TECHNICAL INFORMATION Technical characteristics (liquid state) PRODUCT INFORMATION Technical characteristics (cured state) Description
Duracon 304 is a low viscosity, UV-resistant, 2 component
reactive resin based on methyl methacrylate (MMA) with
many possiblities. In the liquid state it is blue-violet in colour.
After polymerisation the blue-violet colouring is no longer
Duracon® 304 is the topcoat to use when combined prop-
erties of wear resistance, chemical and warm water re-
Please note that an objective comparison with other data is only possible if norms and parameters are identical.
USAGE GUIDELINES
Duracon 304 should only be used as a sealer on Duracon
Substrate preparation
The Duracon system to be sealed must be dry, clean, free
Duracon 304 is suitable for floors within the food processing
of dust and fat. Any fresh Duracon coating system must
be completely cured and cooled down. As a general principle
al Duracon coating systems can be resealed with any
Important advice
Duracon sealer after proper cleaning.
In case of extreme mechanical and chemical loadings, we
For further details, see our „General Preparation and
application guidelines for Duracon floor protection sys-
A permanent water loading can result in a white discoloration
of the Duracon 304 sealer. Therefore always gather waste
or flowing water (particularly hot water) into channels and
convey it into a proper drainage system.
The service durability of the floor can as a result be signifi-
DURACON® 304 HEALTH AND SAFETY PRECAUTIONS
Prior to use Duracon 304 must be careful y stirred to
Suitable protective clothing, gloves and safety goggles
achieve a uniform distribution of the paraffin contained in
must be worn during mixing and application of Duracon
the product. Duracon 304 is thoroughly mixed together
with the Duracon CATALYST (50% dibenzoyl peroxyde),
In case of contact with eyes rinse immediately for a long
in accordance with the below guidelines.
period of time and consult a physician. In case of contact
It should be noted that the amount of catalyst powder to
with skin clean immediately with water and soap.
Duracon 304 is highly flammable; keep away from heat
and al sources of ignition and do not smoke. The stirrer
as wel as al the other electric appliances used on the
application site must be explosion-proof versions.
For further information see our Material Safety Data
TECHNICAL SERVICE
Please contact our Technical Service Department for
Contact RPM/Belgium N.V. / Alteco Technik GmbH.
GUARANTEE
Note: Weight to Volumetric conversion of Catalyst.
RPM/Belgium N.V. and Alteco Technik GmbH warrant al
1 cm³ of Duracon CATALYST weighs 0.64 g
goods to be free from defects and wil replace materials
proven to be defective but give no warranty as to appear-
A compatible pigment powder can be used to colour the
The information and recommendations herein are be-
Duracon 304. Please contact our Technical Service
lieved by RPM/Belgium N.V. and Alteco Technik GmbH to
Application Immediately after the catalyst has been stirred in, the sealer is poured onto the floor in stripes (do not apply directly out of the mixing pails) and distributed onto the coating with a short-pile paint rol er. On slip resistant coatings the sealing can be pre-spread before rol ing with a rubber squeegee. Consumption is approximately 0.3 – 0.6 kg/m², depending on the structure of the substrate. To avoid any possible formation of microbubbles in the seal- er surface it is important to work with freshly mixed mate- rial, i.e. to catalyze smal er batches. For further details see our „General Preparation and ap- plication guidelines for Duracon floor protection sys- tems“.
The information on this data sheet supersedes all previous data concerning this product and its application. The application instructions and the technical data concern-ing our products are indicative. The buyer is responsible for the application, also in respect of third parties. Die Information dieses Datenblattes ersetzt sämtliche frühere
Angaben über das Produkt und seine Anwendung. Die Anwendungsbestimmungen sowie die technischen Daten des Produktes sind lediglich Richtlinien. Der Käufer ist für die Anwendung und Ansprühe Dritter verantwortlich. RPM/Belgium N.V. – Alteco Technik GmbH
The Ottawa County Board of Commissioners held their regularly scheduled meeting at 9:00 AM with the following members present: Gary Wyrick, Chairman, John Clarke and Russell Earls. First Assistant District Attorney Ben Loring was also in attendance. Notice of the meeting was posted at the south door of the Ottawa County Courthouse at 4:39 PM on August 1, 2013. Commissioners’ Meeting Agendas a
DURACON® 304
DURACON® 304